How To Light A Gas Fireplace With Electronic Ignition

The pilot is on, only when the fireplace is operational. This type of ignition system is called ipi, or intermittent pilot ignition.

Image result for fireplace x 4237 cleanface Gas

After the pilot light is confirmed on the electronic unit then allows for the burner to open.

How to light a gas fireplace with electronic ignition. Keep a close eye on your pilot light once you have restored the flame. You can do this by turning the knob to the pilot position. While if it is on a breaker, turn the breaker all the way off and then back on again.

When the furnace shuts off, the valve closes and the pilot light goes out. Don’t forget to check your owner’s manual for instructions on how to light your electric ignition. If the pilot light device is burning with a yellow flame, turn off the gas valve to the fireplace , take the pilot light device apart and clean it.

Once you have given any excess gas a chance to dissipate, follow the instructions in your system’s manual to relight the pilot. When the furnace turns on, a valve opens up and allows the gas to flow to the pilot light. If you have a standing pilot, the gas fireplace will light itself without the need for electricity.

(you can also use a lit match.) About electronic ignition electronic ignition eliminates the wasted fuel of a standing pilot while providing better safety protection. If you release the knob and the clicking stops, you will need to hold the ignition knob in until you see flames begin to catch along the gas line under the logs or tempered glass beads.

The thermopile translates heat from the pilot light to electricity that opens the gas valve so the gas logs can light. This adds up quickly to a few hundred dollars per year. Electronic ignitions all work in much the same way, once the fire is turned on by the user an electronic signal first turns on the pilot light.

With the new ipi systems, that cost is almost entirely eliminated. Electronic ignitions all work in much the same way, once the fire is turned on by the user an electronic signal first turns on the pilot light. Step 4 increase the gas flow going to the fireplace.

The intellifire and intellifire plus use batteries to pilot your gas fireplace during a power outage. Here are a few facts about electronic ignition systems for gas lanterns that you may want to take into account before making a buying decision: Modern gas fireplaces more than likely have an intermittent pilot ignition system.

Some electronic ignition units are now including a battery back up system. After the pilot light is confirmed on the electronic unit then it allows for the burner to open. Often, this will involve manually depressing the pilot valve and using an electric ignitor or match to light the pilot.

Some but not all of the gas fireplaces out there will come with an electronic ignition. A standing pilot light that runs 24/7 will cost you an estimated $.60 per day, depending on the gas prices in your area. If your gas fireplace has an electronic ignition check or replace the fuse.

After you clean and replace the pilot light device, it should burn with a strong blue flame, and it should ignite the fire logs. The traditional method to igniting a fireplace, a match lit ignition system requires the flames be lit manually by holding a matchstick or a long lighter near the burner before opening the gas valve. That’s just under $20 a month, or $75 per season.

Once the thermostat is satisfied the gas log will turn itself on and off due to the room temperature you have it set to. If your power goes out, the milivolt system could be manually turned on to heat your home. Newer generations of gas fireplaces use an electronic ignition system, requiring electricity to start up.

If you’ve checked the breaker and are satisfied, the next place to go is to the electronic ignition check or perhaps a fuse depending on your model of fireplace. The ipi system would not be able to ignite the pilot light manually based on an electronic ignition switch during a power outage. Not all electronic ignition systems have a standing pilot light, but if your superior fireplace does, the light could be out.

Sometimes this is an easy way to fix a gas fireplace that won’t turn on. One can still purchase a gas furnace or water heater with the old standing pilot ignition systems.these systems have been proven reliable and safe over time. An electric spark then lights the pilot light so it can in turn light the burners.

This is the system working to spark the gas to light the pilot. If the fireplace hasn't lit up within 10 seconds, wait at least 10 seconds before trying again. An electronic ignition system does not utilize a standing pilot light.

If the pilot light won’t stay lit, the thermopile may have weakened over time. Most new gas appliances (driers, hot water heaters and forced air systems) are actually required to be manufactured with electronic ignition systems because of the annual fuel savings. Electronic ignition fireplaces save you the cost of running a pilot light 24/7, usually about $8 to $10 a month.

As a result, electronic ignition was developed. Likewise, can you light a gas fireplace without electricity? Place a long lighter next to the burner and pull the fuel trigger.

The next very important step in how to light a gas fireplace is to light the pilot light. You will control the gas flow with a fireplace key (sometimes called a hex key) as you light the fireplace. Press and continue to press down on the control knob while ud press the ignition switch one time per second.

But the ipi switch would not consume gas unless you flipped on the wall switch or used the remote. The first is called an electric spark igniter, which activates the pilot light only at times when it’s needed. You can use your valve to increase or decrease the amount of gas being used to control the height of the fire.

Enter the new electronic ignition systems for your gas fireplace.

Napoleon Vector 38 BuiltIn Direct Vent Propane Gas